I recently installed Wavelink TelnetCE v7.3 on Moto MC9200 series mobile computer. When I copy and paste the telnetCE.exe file to the Windows\startup folder and then reboot I get an error "There is no application associated with wllog.log, Run the app first then open this file from within the application." The application does come up fine but my clients would have to close this dialog box each time the device is booted up. If I don't copy the TelnetCE.exe to the start folder and just launch it, no error. any thoughts?
↧
Wavelink TelnetCE v7.3 on Moto MC9200 series mobile computer "wllog.log" error
↧
Disable Scanner Selection Windows on TelnetCE Startup
Anyone know how I can do this? When I Start TelnetCE a windows comes up
"Scanner Selection" Do you want to use the scanner "Bluetooth SSI Scanner Driver" instead of the Default scanner "External SSI"
I have to hit no to continue with the connection Profile.
Running TelnetCE version 7.3.158
Thanks,
↧
↧
Problem with the deinstallation of the Wavelink TelnetCE 7378 application
I am currently about to deinstall / install the Wavelink TelnetCE 7378 application on our Motorola MC9100 device. In order to achieve this, I have already tried the following measures without any success:
(1) Deinstallation via the Motorola Wavelink Application (Application & Config):
After having executed the deinstallation process I get the following error message despite the fact, that the application is already installed on the device:
"Update failed. Unable to determine install directory. Please verify that the product is installed on the device."
(2) Deinstallation via the remove programs menu on the scanner
It is written on the screen: "Programs in storage memory: Wavelink TelnetCE 7378". I mark the entry. Afterwards I click on "remove". After having clicked on "remove" the following error appears:
"Wavelink TelnetCE 7378 was not completely removed. Do you want to remove it from the list of installed programs?" Then I click on "yes" but nothing happens.
(3) Reinstallation of the client via the "Application & Config" button on the application:
The reinstallation process starts. However I get the following error messages on the screen:
"The previous version of Wavelink TelnetCE 7378 will be removed before the new one is installed. Select OK to continue or cancel to quit". I click on "OK". After three seconds the following error message appears:
"The previous version of Wavelink TelnetCE 7378 cannot be removed. Do you want to continue installing Wavelink TelnetCE 7378?" Here I click on yes. Then the following message appears:
"Installation of Wavelink TelnetCE 7378.cab was unsuccessful."
(4) Restarting of the Scanner and the following of the reinstallation / deinstallation measures (Bullet points 1 - 3) as described above after the scanners’ reboot was also not successful
(5) The deinstallation of the Wavelink Application and the following of the reinstallation / deinstallation measures (Bullet points 1 - 3) as described above after the scanners’ reboot was also not successful
So I have now tried five possibilities to solve the problem. Do you have any other hints regarding the solution of this issue?
Thank you very much in advance.
↧
I've tried several TelnetCE versions on my MC9200 CE7 handheld computer, but keep getting prompted to enter a license when TelnetCE opens. I've tried four different versions and it's always the same result.
I've tried several TelnetCE versions on my MC9200 CE7 handheld computer, but keep getting prompted to enter a license when TelnetCE opens. I've tried four different versions and it's always the same result. I can send the "Application Only" and it installs fine, but as soon as I send the "Config Only" it displays the license error the next time it reboots.
↧
Wavelink TelnetCE 73197 Display Language - UTF8
Hello.
I have Motorola MC3190 and TelnetCE 73197. I need select UTF8 in "Display Language". It is demand for correct display Russian language in the programm. I do not see UTF8 in list "Display Language".
How i do it?
Best regards,
Andrey.
↧
↧
What's the difference between the two purchasable options?
The two options are Terminal Emulation 2 in 1 TN Client vs Terminal Emulation 4 in 1 Client. I'm trying to purchase Wavelink for the MC9500 series.
↧
Multi Session on Android Telnet CE
Hello,
how we can configure multi session on Android version of Telnet CE?
regards,
Sébastien
↧
Motorola 3190Z don't read all the RFID tags
Hi...
with your help I found some solutions to my problems and started to use our Motorola 3190Z handheld, but now I found another little problems with the tags number read by RFID.
I use Telnet CE connected to an iSeries, and I created a program on it that show a video format where there's a field over write the tags datas read by RFID.
I start the program and than enable the RFID reader. All OK!
Start the trigger for to read 138 tags in a cartoon box with 400mm. X 400mm. X 600mm. dimensions and the handheld starts to read them. Every tags readed go to my field on video and automatically wrote in an iSeries database, but here start the problem. It stops its reading operations sometimes at 128, 134, 135, 136, and sometimes the right 138.
I'm near the box, I tried over it, aroung it, at a distance maximum of 50mm. but nothing change. It doesn't read always the right number of tags.
I don't know if the problem is about the passage of the data from iSeries video to database, too slow for the cache of the handheld or if there's a way to calibrate better the reader.
Thanks a lot for the help.
↧
barcode scan error
Wavelink TE Version 7.3.135 on Honeywell Dolphin 7600
Some product barcodes do not scan correctly in the Wavelink Telnet session. For Example; We have a Product Code RN2944 for which we use Free 3 of 9 font to generate a barcode in WordPad. However, when scanned, in the Wavelink session this translates as 792798340
However the same Barcode scans ok in a MS Word session on the same Scanner.
Are there any config settings we can tweak or any other troubleshooting tips?
↧
↧
TelnetCE for MC3190-S
Hello Community,
I've a bunch of MC3190-S (not guns). Please suggest me where to buy Wavelink TelnetCE for this terminal.
Directly from Motorola or from Wavelink?
I've found document on motorola website with part numbers of wavelink telnetce.
Document says that SWE-82990-01 is license 2-in-1 for all device types.
But this site http://www.barcodediscount.com/catalog/symbol/part-swe-82990-01.htm says the following:
Symbol SWE-82990-01
TN Client (Active Sync) for MC55, MC65, MC70, MC75, ES400 and ET1, VT/HP Emulation.
I'm totally confused. Will this part number fit MC3910-S ?
Thanks a lot,
Alex.
↧
I need to be able to select one of 10 host Profiles dependant on the IP address of the mobile device
We are currently in the process of migrating from a system that utilises Avalanche to load balance circa 3500 devices over 10 host profiles.
However, we are no longer able to use this system and have to use a system where we load all ten host profiles on the device and when the device hits a depot network, the correct host profile is selected based on the IP address range the network would assign to the device.
I am no expert in Wavelink but have a modest understanding of the basics.
Using the Script Editor in Telnet, would it be possible to have the device choose the correct host profile dependant on the IP Address of the device, which is assigned to it by the DHCP server?
If the answer to this quandary is yes, would someone be able to give me some pointers as to how I would be able to achieve this please?
↧
Can anyone tell me the key commands to show the menu on a wt4190 unit when it is full screened? with all menus/scroll bars hidden? I have done this before but cannot remember the keys.
Can anyone tell me the key commands to show the menu on a wt4190 unit when it is full screened? with all menus/scroll bars hidden? I have done this before but cannot remember the keys.
Thanks,
Paul.
↧
Is Picklist Mode available on the PreLicensed MC9190 CE
Is Picklist Mode available on the PreLicensed MC9190 CE Operating System. I have downloaded and installed the MC9190 CE Emulators v7.0.122. Once it is installed on the PC I then go to Scanner/Common and expect to see "Pick List Mode". On the MC9190 CE TE there does not seem to be Pick List, however on the MC9190 WM TE there IS a "Pick List Mode".
↧
↧
IOS Terminal Emulation with Bluetooth scanner
I have an Ipad that I am using with the Terminal Emulation software. My issue is that my bluetooth scanner will not work with the emulator. Does anyone know if support for bluetooth scanners has been added?
↧
Problem: When typing in Wavelink Industrial Browser sometimes the keyboard will log 2 key strokes instead of 1. Has anyone seen this issue with TE 7.3.237?
When typing in Wavelink Industrial Browser sometimes the keyboard will log 2 key strokes instead of 1. Has anyone seen this issue with TE 7.3.237?
↧
Telnet emulator session block
Hello,
Our warehouse logistics are handled through an internal ERP application ensuring a proper flow of the reception and distribution of auto parts.
For this purpose we use around 110 mobile terminals with barcode scanners (RF Guns) of which 50 are deployed in the central warehouse.
The models used are:
Motorola MC2100
Datalogic Falcon X3
Datalogic Skorpio
In the central warehouse we are currently using 50 Motorola MC2100 scanners with Windows CE 6.0 operating system. As an emulator we are using Wavelink Corporation’s Telnet version 7.3.63 for Motorola MC2100 terminals.
Lately, the following problem began to manifest itself:
On a daily basis every Motorola MC2100 device suffers one or more unexplainable telnet session blocks.
When this happens, the terminal cannot interact with the application any more, the keyboard stops working and after a few minutes the display shows the "disconnected session" message. The terminal’s log doesn’t record any loss of connection to the access point.
The Access Points are all newly acquired from Motorola in order to ensure maximum compatibility between them and the mobile terminals.
Our question is:
To what extent the Telnet emulator may influence these session blocks, taking into account the following:
1. Telnet version
2. Certain parameters of the telnet configuration
3. “Avalanche Enable” configuration – we are using the Avalanche platform version 5.3.0.572 to manage our terminals
4. Having a large number of sessions (high load) on an Access Point.
Can you please help us with any idea in tackling this problem? Is there a log monitoring tool that can help us to identify the cause of these problems?
The situation is very critical and this seriously influences the process of delivery and reception of goods.
Thank you,
Florian Baloi
↧
how recovery a license from TelnetCE Version 7.3.74
I register a incorrect model of handheld and generate the license for an this incorrect model
↧
↧
How to have loudly sound on MC3190?
Hello,
on MC3190 when we use Telnet CE ( any version) the level of the sound is not enough loud to be hear by a end user in the warehouse
we need to know how we can set correctly TelnetCE to have a very heavy sound
thanks
Sebastien
↧
how to print to a zebra bluetooth portable printer?
Having trouble printing to a zebra bluetooth portable printer. Looking for some tips regards configuration and or coding etc.
↧
Does Wavelink TelnetCE support Chinese (We are using a Motorola MC9190-G gun)?
Does Wavelink TelnetCE support Chinese (We are using a Motorola MC9190-G gun)?
When We look for Chinese in the localization configuration, We do not find the Chinese option.
¿Should our MC9190-G have a Chinese-localized WinCE for the TelnetCE software to support Chinese?
Please advice.
↧